Powerful Data Logger and Flexible Data Acquisition and Data Logging Systems
|
Datataker Open Source Software G-plot dataTaker Active X control Pre-requisite: Knowledge of Advanced Windows Programming The Dump_DBD command line utility converts DBD files to readable ascii data. If you need a specific output format then you may need to modify the supplied source code to suit. The source was compiled with Microsoft Visual C/C++ 97. It is fairly straightforward C++ code that should easily be ported to other compilers and environments (e.g. GCC, Linux). dump_dbd.zip Download (44 KB Zip 5-May-2008) LabVIEW Examples The following programs have been written to demonstrate applications using the dataTaker Instrument Driver for LabVIEW. There are further examples included in the driver, which demonstrate the use of the various dataTaker VIs. They can be selected from the User Libraries section of the functions palette in the block diagram. Demo DT800 SSP Written in LabVIEW 7.1 This allows a user to demonstrate some functions of LabVIEW using the DT800 data logger with the Sensor Simulation Panel. The program will do the following. 1) Prompt the user to select one of the available serial ports 2) Test to see if a dataTaker data logger is on the select serial port 3) Clear any data and set the data logger to a default state 4) Write a new program to the data logger 5) Test the serial port, and if any data is on the port, read and display the data 6) Carry out any user requests using events 7) Close the program when requested by the user The progam includes a number of VIs used on the dataTaker Weather Station http://weather.datataker.com.au/ Download (1.1MB Zip 22-Dec-2006) Demo DT500 SSP Written in LabVIEW 7.1 This allows a user to demonstrate some functions of LabVIEW using the DT500 data logger with the Sensor Simulation Panel. The program will do the following. 1) Prompt the user to select one of the available serial ports 2) Test to see if a dataTaker data logger is on the select serial port 3) Clear any data and set the data logger to a default state 4) Write a new program to the data logger 5) Test the serial port, and if any data is on the port, read and display the data 6) Carry out any user requests using events 7) Close the program when requested by the user The progam includes a number of VIs used on the dataTaker Weather Station http://weather.datataker.com.au/ Download (1.2MB Zip 22-Dec-2006) Solar Weather Station This software was developed in LabVIEW 7.0 The program demonstrates a simple application, writing a program to a data logger, then reading and displaying the data. Solar weather station.vi was written for a DT50, connected to com port 1, at 9600 baud rate, 8 data bits, one stop bit, no parity, and XON/XOFF flow control. solar weather station 800.vi was written for a DT800. You will need to specify the IP address you use in two locations. In the block diagram, under the "Start" selection of the case structure, and the "Initialise" selection of the case structure. You will see the string constant, labelled "IP address" Download (166KB Zip 22-Dec-2006) Simple Plot Written in LabVIEW 6.0.2 This program plots a graph of the historical data of data logger The VI assumes that the connection is correctly identified, there is a program running on the dataTaker datalogger, and the data is logged with the LOGON command. Ensure you select the correct connection type, and the correct connection settings relevant to your connection. Download (242KB Zip 22-Dec-2006) |
 HomeProductsStock AvailabilityEnvironmental MonitoringGeotechnicalArticlesTrainingFAQ
SupportTechnical Support Inquiry Technical Reference Manual Downloads Forum Tech Notes Techincal Support Charter Customer Survey Form What's NewCatalogue of MarketingContact UsAboutSite Map Weather StationGrant Data Loggers |
Home |
Products |
Downloads |
Forum |
Exhibitions |
Newsletters |
Workshops |
Contact Us
Copyright ©
Datataker Pty Ltd